Long ago and far away (20+ years and 300+ miles) I was just starting to reload rifle rounds. I probably wasn’t using the proper lubrication and I got a 30-06 case stuck in this die:

I concluded it was impossible to get the case out and I went to the local gun shop to see if they had a replacement die I could purchase. The owner of the store, a wise and knowledgeable man, suggested I order a case extraction tool rather than purchase a new die. I did so, but it took far longer for the tool to arrive than I had patience for and I got another die anyway. A neck resizing only die.

When the tool did arrive I was looked at the situation and realized I needed to drill out the primer pocket (drill provided with the tool), tap the resultant hole (tap provided), use a cup like piece of metal with a hole in the “bottom” through which a bolt was screwed into the base of the shell casing, then tighten the bolt to pull the case out of the die. That should work! Except for one problem. The depriming pin and expander ball were inside the case and blocking the drilling and tapping operations. I was unable to remove them from the case up through the top. In fact you can see the broken top of the spindle (is that the correct word for this?) in the picture above from my attempts to unscrew it from the die. I didn’t really need the full length resizing die at the time and left the stuck case in the die.

20+ years later I started to reload 30-06 again and I needed to do full length resizing with some used brass I had purchased a year or so ago. I got out the full length resizing die and discovered the stuck case. Crap. As I shuffled through my die supplies I stumbled across the case removal tool and reevaluated the situation. I really needed to figure out how to get the depriming pin and expander ball out of the case. After way too long I realized something.

In the picture you will see four different knurled sections to the die. The top two are associated with the spindle. I removed these, squirted some case lube into the top of the die, turned the second one upside down so that it didn’t thread itself back into the die main body and tightened it up. It was a hard pull but the expander ball came back up through the case which had been stuck for 20+ years.

I drilled and tapped base of the case and successfully extracted the case with the case extraction tool I had purchased so many years ago. See the case on the left below compared to the normal case in the center:

I expressed my joy and cleverness to Barb, reassembled the die, adjusted it, lubed up a bunch of cases and started resizing them. On about the fourth case I stupidly picked up an lubed case sitting on the bench and got it stuck.

This time it only took about 10 minutes, instead of 20+ years, to get the case out. See the case on the right above.

What I found most interesting was that the stuck cases had necks which were stretched a full 0.150 inches. Previously stuck cases on the left and right compared to a normal case in the center:

There are multiple factors contributing to the shortage of primers. I had previously heard or assumed most of them in the following post. But the Remington component to “The Great Primer Shortage of 2020.” was new to me.

From Powder Valley, Why Is There a Primer Supply Shortage?

Demand, however, is just one part of the story. Disruptions in the supply chain have also made a big impact on the availability of primers. When it comes to ammunition supplies, bullets are easy to manufacture, brass can be re-used, and powder is generally stockpiled by companies (though perhaps not the kind you’re looking for). This leaves primers, which are relatively difficult to make, as the component that causes the bulk of ammo shortages.

In the U.S., only four companies (Winchester, Remington, Federal, and CCI) manufacture primers for civilian use, law enforcement, and the military. Even under perfect circumstances, there’s only so much they can produce at once, and needless to say, circumstances have not been perfect during the pandemic. People getting sick, missing work to take care of their kids, and self-quarantining – from factory workers to delivery drivers, and all throughout the supply chain – caused a lull in manufacturing this spring.

The Remington bankruptcy has had a large impact on the shortage of ammo and primers.  With Remington in a state of financial insolvency for the past two years, suppliers were demanding payment upon delivery for products.  Remington simply did not have the financial capabilities to have an abundance of raw materials on hand and had to shutter some of their production capacity.  Barnes bullets and primers were hit particularly hard in the reloading market.  With the recent purchase of Remington by Vista, there is a good chance that Vista will be diverting CCI and Federal primers that would typically go to reloaders to Remington ammunition production.  Remington primer production capacity has never been great.  The hope would be that Vista will place more emphasis on getting the Remington primer production capacity increased substantially and quickly.

I have 1,000 CCI and 2,993 Winchester large pistol primers that, at the current consumption rate, I’ll consume sometime after Donald Trump Jr. finishes his second term.

As primers are essentially impossible to get right now I thought I would sell them to someone that could use them. I’m selling them at the inflated price of $40/1,000 or I’ll trade them for an equal quantity of small pistol primers.

I don’t want to ship them. If you can meet me in the Bellevue area that works. Or I’ll probably be driving to Orofino Idaho sometime in the next couple of weeks. If you can meet me somewhere along the path of Bellevue, Vantage, Colfax, Troy, Kendrick, Cavendish, Lewiston, and Orofino* that would work too.

* No. That not the exact path. But either coming or going I will visit all those towns.

Via email:

From: dj
Sent: Wednesday, September 2, 2020 9:44 AM
To: Joe Huffman
Subject: IMR 5010, Bofors, Others

Greetings Joe

A friend of mine is one of the late Bill Steigers’s sons – developer of Bitterroot Bullets in Lewiston, ID.  We were going through some of Bill’s leftover reloading supplies recently and came across several (full and partial) 20# canisters of old surplus reloading powder, including IMR 4831, H4831, Red Dot, Bullseye, DCM 4895 and some “flavor” of Bofors. There was also a large (original) box (originally weighed 150#) of IMR 5010.  I’d estimate that there are 30-40# remaining in it.

Some of the canisters are unopened. I inspected the ones that were open and all smelled OK, and appeared dry and in otherwise good condition. 

Bill’s son isn’t a ‘gun guy’ so I’m helping him out. I’d never be able to use even a small fraction of any of that powder, so I’m reaching out to anyone who might be plugged into a network of reloaders to see if anyone has any interest in any of this stuff.

Thank you.

Dan
Bonners Ferry, ID

If anyone has an interest send me an email (blog@joehuffman.org) and I’ll forward it on to Dan.